變速箱升擋緩慢是指在汽車行駛時，升擋車速明顯高于標準值，升擋前發動機轉速翩高，必須采用加速踏板提前升擋的操作方法(即松開加速踏板幾秒后再踩下)才能使自加速無力有很多原因，常見的就是油泵油壓達不到，活塞環.氣門等密封不嚴跟火花塞跳火強度也有關系。另外再清洗一下噴油嘴。
The slow upshift of the transmission means that when the vehicle is driving, the upshift speed is significantly higher than the standard value, and the engine speed is high before upshift. The operation method of upshifting in advance of the accelerator pedal must be adopted (i.e. release the accelerator pedal for a few seconds and then press it) to make the self acceleration weak. There are many reasons. The common one is that the oil pressure of the oil pump cannot reach the standard value, and the piston ring The lax sealing of valves is also related to the spark plug spark strength. In addition, clean the fuel injection nozzle.
出現自動變速器升擋緩慢的情況，可能是換擋電磁閥出現故障導致。如果是偶發性故障，一般可以通過消除故障碼或者升級程序來解決因此，若在P擋狀態下行強拖動車輛，必然造成自動變速器外殼的損壞，導致重大損失;同時，在上下坡停車時，也不要僅僅使用P擋制動車輛，而應該牢牢拉緊手制.。
The slow upshift of automatic transmission may be caused by the failure of shift solenoid valve. If it is an accidental fault, it can generally be solved by eliminating the fault code or upgrading the program. Therefore, if the vehicle is forced to drag in the P gear state, it will inevitably cause damage to the automatic transmission housing and heavy losses; At the same time, when parking uphill and downhill, don't just use p gear to brake the vehicle, but firmly tighten the hand brake.
汽車提速提不起來，需要進行如下幾種方法:使用汽車診斷電腦檢測是否有故障碼，排除故障后就能修復。自動擋提速慢油耗高，反正原因較多，油頭，氧傳感器，節氣門，變速器，耦合器，正時，燒機油，要逐步檢測才行。壽命比手動變速器低，易耗品，每隔一段時間必須保養。
The car can't speed up, so we need to carry out the following methods: use the car diagnostic computer to detect whether there are fault codes, and repair them after troubleshooting. The speed of automatic gear is slow and the fuel consumption is high. There are many reasons anyway. The oil head, oxygen sensor, throttle, transmission, coupler, timing and oil burning should be tested step by step. The service life is lower than that of manual transmission. It is a consumable and must be maintained at regular intervals.
車輛更換齒輪油后提速變慢了，這是什么原因導致的？這個很有可能是齒輪油粘度不對造成的，也就是換了不對的變速箱油。換油之前應該好好看看說明書，對車輛所使用的油水型號，粘度，等級，技術指標等等要心里有數。如果齒輪油選型不對，就會出現，冷車掛檔生澀，熱車后，行駛中降檔不順暢，容易出現卡齒現象，而且，怠速時候，方向盤，變速箱的抖動明顯增大。
The acceleration of the vehicle slows down after changing the gear oil. What is the reason? This is probably caused by the wrong viscosity of the gear oil, that is, the wrong transmission oil is changed. Before changing the oil, you should take a good look at the instructions and know the oil-water model, viscosity, grade, technical indicators, etc. used by the vehicle. If the gear oil is not selected correctly, it will appear that the gear shift of the cold car is astringent, and after the hot car, the downshift is not smooth during driving, which is easy to get stuck. Moreover, when idling, the jitter of the steering wheel and gearbox increases significantly.
濟南自動變速箱維修人員建議看看車輛說明書，查找適合本輛車用的手動變速箱油型號。如果齒輪油性能低下也會造成掛檔生澀，更好用福斯的手動齒輪油。這是由于你更換的齒輪油的品質不高，導致不能給齒輪起到一個潤滑的作用。換完變速箱油后因為是新油，還比較粘稠，所以變速箱換擋會稍有緩慢。過段時間就好了。
Jinan automatic transmission maintenance personnel suggest looking at the vehicle manual to find the manual transmission oil model suitable for this vehicle. If the performance of gear oil is low, it will also cause astringency in gear. It is best to use Flowserve manual gear oil. This is because the quality of the gear oil you replace is not high, so you can't lubricate the gear. After changing the transmission oil, because it is new and viscous, the transmission shift will be slightly slow. It'll be fine in a while.
如果變速箱油多了淹過行星齒輪，產生大量的氣泡，氣泡會在油里面，影響正常的油壓。油的壓力是很大的，氣的壓力相對要小很多，所以壓力才不夠用。變速箱出現故障很大的原因是閥體太臟導致的，變速箱閥體臟太臟會破壞變速箱油的質量和摩擦特性。加大摩擦和磨損，同時油泥也會在變速箱內產生，造成閥體和管路堵塞，無法順序實現對油壓的調節，從而出現變速箱故障問題。
If the transmission oil is too much, it will flood the planetary gears and produce a large number of bubbles, which will be in the oil and affect the normal oil pressure. The pressure of oil is very high, and the pressure of gas is relatively much lower, so the pressure is not enough. The main reason for the failure of the transmission is that the valve body is too dirty. The dirty valve body of the transmission will damage the quality and friction characteristics of the transmission oil. Increase friction and wear. At the same time, oil sludge will also be generated in the gearbox, resulting in the blockage of the valve body and pipeline, which can not adjust the oil pressure in sequence, resulting in the problem of gearbox failure.
The reasons for the slow shift and slow acceleration of the automobile gearbox are the above. If you have other problems to solve, you can come to our website www.jnbsx Com.
