說到濟南自動變速箱維修，其實有很多事項都需要我們注意，我們不僅需要知道在變速箱維修的過程中需要經歷拆卸步驟，下面來講講相關事項吧。
When it comes to the maintenance of Jinan automatic transmission, there are many matters that need our attention. We not only need to know that we need to go through the disassembly steps in the process of transmission maintenance. Let's talk about related matters.
變速箱的拆卸步驟：
Disassembly steps of transmission:
①準備好工具及盛放各類零件的小盒,在干凈平整的操作臺上進行解體.如果沒有該車的維修手冊,應準備好記錄本和做記號的膠布條.
① Prepare tools and small boxes for various parts, and disassemble them on a clean and flat operating platform. If there is no maintenance manual for the vehicle, prepare a record book and a tape for marking
②拆卸應從前部油泵開始，由前至后，由外及里地逐步進行，并隨時做好記錄。
② The disassembly shall be started from the front oil pump, from front to back, from outside to inside, and records shall be made at any time.
③自動變速器殼體大多用鋁合金鑄成，拆卸時，嚴禁使用撬棍和鐵器直接敲打。
③ Most of the automatic transmission housings are made of aluminum alloy. When disassembling, it is strictly prohibited to use crowbars and iron tools to directly knock.
④拆卸液控閥體時，應小心仔細，上下閥體分離時要防止滾珠，卡環等掉地，要準確記住正確位置。
④ When disassembling the hydraulic control valve body, be careful. When the upper and lower valve bodies are separated, prevent the balls and snap rings from falling to the ground. Remember the correct position accurately.
⑤拆檢單向離合器時，須注意其正確的配裝方向，裝合時，決不能顛倒。
⑤ When disassembling and inspecting the one-way clutch, pay attention to its correct assembly direction, and never reverse it during assembly.
⑥零件拆卸后，應用汽油洗凈，并用低壓壓縮空氣吹干，不得使用易掉纖維的棉紗等擦拭閥類零件。
⑥ After the parts are disassembled, they shall be washed with gasoline and blown dry with low-pressure compressed air. It is not allowed to wipe the valve parts with cotton yarn that is easy to lose fibers.
⑦墊上O型密封圈等易損件原則上拆卸后應更換新件，不得湊合重復使用老公、變形、磨損的易損件。
⑦ In principle, the O-ring and other vulnerable parts shall be replaced after disassembly. It is not allowed to reuse the worn, deformed and worn vulnerable parts.
⑧新離合器片、制動器片應在變速箱油中浸泡，待吸足油后才能裝合。
⑧ The new clutch plates and brake plates shall be soaked in the transmission oil, and can be assembled after absorbing enough oil.
⑨閥芯、活塞、密封件等裝合時，均應涂上變速箱油。
⑨ When the valve element, piston and seal are assembled, they shall be coated with transmission oil.
⑩裝合時，嚴格按規定力矩擰緊螺釘。
⑩ During assembly, tighten the screws in strict accordance with the specified torque.
If you want to repair by yourself, you may be able to do it yourself if you simply replace the parts. However, if it involves the overhaul of the gearbox, I suggest you go to a professional repair shop to deal with it. For more information, please visit our website http://www.566605.com Consult and understand!
